LED Lamp Aging Test Process
- Categories:Industry News
- Author:Fiona Lau
- Origin:
- Time of issue:2020-06-09 10:09
- Views:
(Summary description)Standard LED lamp aging test process is to reduce the improper operation caused by damage to the lamp, improve the aging test efficiency and ensure the quality of lamps to prevent the occurrence of security incidents.
LED Lamp Aging Test Process
(Summary description)Standard LED lamp aging test process is to reduce the improper operation caused by damage to the lamp, improve the aging test efficiency and ensure the quality of lamps to prevent the occurrence of security incidents.
- Categories:Industry News
- Author:Fiona Lau
- Origin:
- Time of issue:2020-06-09 10:09
- Views:
In order to prevent the quality problem of LED luminaires caused by the damage of LED luminaires, or to prevent LED luminaires in the packaging process damage, LED products need to be used for aging testing with LED aging line. Aging testing with LED aging line is an essential part of the production of LED lamps, but also the aging test of LED products is an important measure to ensure the reliability of electronic products, is the final essential step in product production. Let us get to know this, what is the LED Lamp Aging Test Process and how to operate it.
1. The purpose
Standard LED lamp aging test process is to reduce the improper operation caused by damage to the lamp, improve the aging test efficiency and ensure the quality of lamps to prevent the occurrence of security incidents.
2. The environmental requirements
The temperature is 20 ℃ -35 ℃, the humidity is 55% -95%.
3. The test tool
Aging rack (requiring aging of the DC power supply and AC power supply and power supply grounding)
4. The aging test method
4.1 Semi-finished or immersion products after the light on the aging frame, according to the product input voltage connected to the corresponding power supply seat.
4.2 Open the switch of the aging test stand, according to the different input voltage to close the corresponding power switch to check whether each lamp has been lit, while ensuring that the lamp in the aging process full power work.
4.3 Aging test time for more than 8 hours. If the lamp in the aging process, the lamp is not less than the pass, power test, each power 20s, power off 20s, in the aging process every 2 hours to To carry out lighting. (Method is to pick up the lamp by hand in the aging frame jitter or proper taps) aging time lamps can not appear dead lights, dark lights, flashing, color cast and other undesirable phenomena.
4.4 Aging according to different lamps according to different procedures for aging, aging is completed, close the aging test stand switch, to be the surface temperature of the lamp down to room temperature, the lamp from the aging test rack removed, placed in the designated location to wait for the next process The
4.5 In the process of aging, such as the above description of the adverse phenomena should immediately stop testing, the defective products removed from the aging rack and do a good job record bad, bad product delivery service department to deal with.
4.6 Aging staff every 2 hours to do the aging record table.
4.7 Quality department IPCQ every 2 hours inspection of an aging frame, check the aging test is the normal lighting, the aging of the lamps and lanterns to identify the same time, check the aging time of the lamp, the shelf time, the aging records recorded in the inspection On the record sheet, when the abnormal rate of aging exceeds 3%, IPCQ must respond to the situation to the quality supervisor.
4.8 With the control of the lamps, must be installed according to the installation of wiring diagram aging, after-sales staff must cooperate with the production of aging.
5. Safe operating matters needing attention
5.1 The aging test should be carried out by the designated personnel, the operation must be done during the safety protection measures.
5.2 AC220V input of the lamp in the aging test when the lighting of the ground must be connected, absolutely no ground line for testing.
5.3 In the testing process must always pay attention to the status of lamps, to be regular inspection by hand.
5.4 On the lower frame to grasp the lamps, to prevent the lights fall injured the body.
Scan the QR code to read on your phone
TEL: +86-0755-86369100
E-MAIL: Sales010@longsun-led.com
ADD: Room 304, Block B, Building 7, Shenzhen International Innovation Valley, Dashi 1st Rd., Xili Community, Xili St., NanShan Dist.,ShenZhen
Copyright © Shenzhen Long Sun Optoelectronics Technology Co., Ltd 粤ICP备20036433号